Ekofires EKO 3080 Troubleshooting Guide

installation and user instructionsAll instructions must be handed to user for safekeepingRevision B - 03/11Country(s) of destination - GB/IEeko 3030 e

GAS SUPPLY ROUTING (continued)Eko 3030, Eko 3035 and Eko 3060, Eko 3065 models : The appliance firefront is notched to allow the gaspipe to pass throu

FITTING THE BURNER UNITImportant Note: Check the thermocouple nutconnection into the rear of the valve is secure.Temporarily fit the burner unit and

OPERATING THE FIRE(remote control models)The pilot is visible through the left hand side of the front ceram-ic strip. Turn the main burner control (sh

FLUE SPILLAGE MONITORING SYSTEMThis fire is fitted with a flue spillage safety device (ODS). If the fire shuts down during use for no apparentreason t

SERVICING (continued)4. Remove the two screws that retain the data/control plate. 5. Disconnect the gas supply, and remove the two securing screws in

TROUBLESHOOTING GUIDEFire sparks but pilot does not light No gas to fire, check isolators are open.Pipework blockage, clean out.Air not fully purged,

USER INSTRUCTIONSIMPORTANT NOTESThe installation of this fire MUST only be carried out by a GAS SAFE registered person in accordance with the GasSafet

CLEARANCES TO COMBUSTIBLESA combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensionsgiven below.A non

FUEL BED LAYOUT (coal effect models) - continued3. Open the bag of 16 moulded coals. All of thecoals are the same. Take five coals and place themas sh

FUEL BED LAYOUT (continued)2. Open the bag of 16 ceramic pebbles. All of thesepebbles are the same size. Take five pebbles andplace them as shown. Car

Eko 3030Eko 3040Eko 3050Eko 3060Eko 3080Please note : Except whereotherwise stated, all rights,including copyright in thetext, images and layout ofthi

FUEL BED LAYOUT - (Log effectoption) - (Eko 3030, Eko 3035, Eko 3080, Eko 3085,Eko 3090, Eko 3095 models only) continued2. Open the bag of 9 moulded c

OPERATING THE FIRE (manaul control models)The pilot is visible through the left hand side of the front ceramic strip.Rotate the coals or pebbles for g

FLUE SPILLAGE MONITORING SYSTEMThis fire is fitted with a flue spillage safety device (ODS). If the fire shuts down during use for no apparentreason t

INSTALLATION INSTRUCTIONSPreliminary Notes Before InstallationThis appliance is an Inset Live Fuel Effect appliance that provides radiantwarmth utilis

IMPORTANT NOTESThis fire is an Inset Live Fuel Effect Gas Fire providing radiant warmth. It is designed to operate on NaturalGas only.It is the LAW th

INSTALLATION REQUIREMENTSThis appliance MUST NOT be installed into a room containing a bath or shower, or where steam may bepresent. The fire has been

SITE REQUIREMENTSThe fireplace opening should be inspected and repairs made where necessary. Any chair brick or fireback maybe left in situ, providing

SITE REQUIREMENTS (continued)A non-combustible shelf may be fitted to within 10mm of the top edge of the fireframe. Combustiblematerials, such as wood

UNPACKING THE APPLIANCEStand the carton the right way up, cut the strapping bands and remove the top endcap. Read all the instruc-tions before continu

PREPARING THE APPLIANCE(continued)SPIGOT RESTRICTOR (All models): If installing the fire intoa Class 1 or good Class 2 flue, simply bend up (stitch be